A novel electrochemical plating process for depositing gold and silver surface finishes using environmentally benign,
organic-based solutions as the plating bath is being investigated. The plating bath solution consists of an extractant and a
diluent of the types used in conventional organic solvent extraction. The organics are very poor electrolytic conductors and
can sustain only short range electrochemical reactions. The deposition mechanism involves the dissolution of a less noble
substrate metal with the simultaneous deposition of more noble metal particles on the surface of the substrate,similar to
immersion plating in an aqueous solution. Feasibility of the concept was demonstrated by loading the organic extractants
with gold or silver in the form of complexed ions. The metal bearing organic liquid was then placed in contact with blank or
patterned copper and nickel surfaces commonly used in the printed circuit board industry. Deposition of a continuous,
adherent gold and silver surface finishes from the organic liquid was achieved with the proper processing conditions. Gold
and silver films were deposited only on the exposed metallic surfaces of the substrate,indicative of a selective area
deposition process similar to immersion plating. Scanning electron microscopy (SEM) indicated that the films were
composed of nanometer sized particles.

Process,Process,Process – these words must ring loudly in our ears,and must be at the forefront of lead free
implementation. The smaller process windows dictated by lead free alloys are going to put greater demands not only on
reflow equipment,but also on first article inspection equipment and procedures. This article will highlight the typical process
concerns associated with lead free alloys with respect to proper first article inspection,qualification of a lead free SMT line,
and adherence to ISO and Six Sigma Quality Management Philosophies. An effective quality control program is completely
dependent on the capability of discovering all possible process problems in order to insure prevention. The enormous
financial and reputation costs of warranty failures faced by leading mass production manufacturers can be greatly reduced by
improving the first article inspection process.
Much has been published concerning the smaller process windows associated with lead free alloys,and their influence on
reliability issues. It is suffice to say that the soldering process up until today has been most forgiving to process problems.
Lead containing solder pastes have known extended soak ranges from 60 to 120 seconds,as well as broad acceptable peak
ranges from 205°C to as high as 255°C. Large temperature deltas in the current soldering process were less problematic for
solderability and reliability. Lead free alloys will see much smaller process windows for soak,and a peak range from 230°C
to 250°C. Working outside these specified process windows will have a negative impact on solder joint integrity,component
safety,and ultimately on reliability.

The popularity of low voltage technologies has grown significantly over the last decade as semiconductor device
manufacturers have moved to satisfy market demands for more powerful products,smaller packaging,and longer battery life.
By shrinking the size of the features they etch into semiconductor dice,IC manufacturers achieve lower costs,while
improving speed and building in more functionality. However,this move toward smaller features has lead to lower
breakdown voltages and increased opportunities for component overstress and false failures during in-circuit test.
The chief reason is that testers designed for boards that traditionally operated with a power supply voltage of 5V are still
being used on new generation ICs,which operate on 2.5V,1.5V,or even 0.8V. These traditional in-circuit testers often do
not have the accuracy,safety,and reliability features that are required to test low voltage technologies.
This paper discusses the challenges of performing powered-up vector testing of low voltage technologies on traditional incircuit
testers and describes the safeguards that are necessary to ensure that test vectors do not violate the increasingly tight
specifications of low voltage parts.
It also describes the in-circuit test features that are most important for testing low voltage technologies: independently
programmable,high accuracy driver/sensors; real time dynamic backdrive current measurement,programmable backdrive
control,specialized digital controller; and multiple level digital isolation.

Evaluation of printed wiring boards (PWBs) for thermal reliability during assembly and rework operations by Thermal
Mechanical Analyzer (TMA) “T-260” testing has been an accepted practice for many years. Test procedures are specified in
IPC-TM-650-2.4.24. It is common to see finished PWB T-260 requirements of 2 minutes or greater. In general PWBs
produced using FR4 substrates pass this requirement. Recently,however,T-260 results from PWBs of thickness greater than
8mm,produced with high Tg FR4 substrates,using industry standard TMAs supplied by two manufacturers have
delaminated in less than 2 minutes. Samples 4mm thickness or less produced with the same substrate materials consistently
survive. Significant variation of the measured glass transition temperature (Tg) has also been observed. Tgs measured by
TMA for the very thick PWBs are significantly lower than those measured for thinner PWBs.
When T-260 samples are examined following the testing,the delamination is always observed to be on the top few layers of
the PWB. This is true even for thin samples. The sample is significantly degraded at the top surface with the resin bubbled
and charred while the bottom of the PWB resting on the sample stage is not significantly different from the pre-tested sample
(Figure 1). These results suggest that the thickness of the sample and instrument used are influencing the T-260 time to
delamination. To better understand the influence of the sample thickness and instrument set-up on T-260 and Tg results
several studies were performed.

Non-destructive testing during the manufacture of printed wiring boards (PWBs) has become ever more important for
checking product quality without compromising productivity. Using x-ray inspection,not only provides a non-destructive test
but also allows investigation within optically hidden areas,such as the quality of post solder reflow of area array devices (e.g.
BGAs,CSPs and flip chips). As the size of components continues to diminish,today’s x-ray inspection systems must provide
increased magnification,as well as better quality x-ray images to provide the necessary analytical information. This has led to
a number of x-ray manufacturers offering digital x-ray inspection systems,either as standard or as an option,to satisfy these
needs. This paper will review the capabilities that these digital x-ray systems offer compared to their analogue counterparts.
There is also a discussion of the various types of digital x-ray systems that are available and how the use of different digital
detectors influences the operational capabilities that such systems provide.

The behavior of BGA solder joints under dynamic loads has become more significant in recent years. This work explored test
methodologies for solder joint failure evaluation under dynamic loads. The objectives of this study were
• To evaluate the behavior of solder joints under a variety of strain rates as seen during both 4 point bend testing and
mechanical shock
• To try to quantify the shock levels present at solder joint failure to support ongoing solder joint reliability modeling
efforts
A test coupon and fixture developed for the four point bend test setup is reviewed. Testing was performed under different
strain rates and the results showed clearly that the solder joint failure is strongly strain rate dependent under mechanical
bending load on boards. This implies that the practice of low strain rate (quasi-static) test with dynamic amplification factor
for solder joint failures,such as the four point bend test,is not sufficient for dynamic prediction due to over-estimation of the
joint strength at low strain rate range. The finite element analysis revealed that the strain rate dependent material properties of
the solder play the key role of solder joint failure threshold.
Comparison of strain rates between the four point bend test and a more traditional mechanical shock test were made on a
desktop motherboard. These tests showed that the strain rate is much higher during the mechanical shock test than that seen
during the bend testing. A variable mass shock test and an incremental shock test procedure were developed to evaluate BGA
solder joint shock failures. In-situ solder joint continuity was monitored during the shock events. The results of these tests
give a good estimate of motherboard BGA solder joint robustness.
In addition,a shock test fixture and a test vehicle were developed similar to those used in the four point bend test. By using
the incremental shock test procedure outlined above,the acceleration level (G-level) at solder joint failure was obtained. This
information was input to the finite element dynamic analysis,the overall behavior of the test coupon during shock was
simulated and the solder joint failure force obtained. Failure analysis of the shocked boards revealed that PCB pad/FR4
disbond was the dominant failure mode for the tested eutectic solder joints. In addition,fracture at IMC between pad and
solder on the package side was observed.
In summary,a set of test and modeling methodology for solder joint reliability evaluation under dynamic load was developed
and validated and some recommendations are made as to the applicability of these test methods.

Industry cost control pressures and technology drivers demand more powerful 3D AOI machines for control of solder paste
printing. Here is an inside look at the factors potential purchasers of these systems should take into consideration.

The electronic industry trend of smaller component packages and tighter spacing has put greater demands on manufacturing
for process control and product verification. Defects must be caught earlier in the process to provide feedback to the process.
Large quantities of manual rework on components that can barely be seen or handled put too much strain on rework
operators. Manual inspection as a means of process control has become less effective by these factors causing fatigue,
missing defects,and reduced thru-put. In-circuit test as a means of product verification also has issues because it requires
space on the printed circuit board for test pads. Automated Optical Inspection (AOI) is an increasing popular method to
address process control and product verification. Faster processors with higher density memory devices have enabled image
capture and processing to become a viable alternative. This paper will detail the methodology used to select and evaluate AOI
systems as an alternative process control and product verification tool.

Conductive adhesives (CAs) have been an important problem-solving class of assembly materials for decades,but primarily
as die attaches products,ever since they replaced metallurgical systems. Renewed and intensified interest in lead-free (L-F)
electronic assembly has moved CAs back into the spotlight. Although lead-free solders,both new and very old,have been
studied for several years,they are a partial solution at best. One may conclude that: (1) lead-free alloys do work,(2) there is
no drop-in replacement,and (3) their higher processing temperatures are detrimental.
The expected increase in soldering temperatures is cause for concern over potential damage to laminates,packages and some
semiconductors. New alloys will also require modifications to some soldering equipment. High temperature L-F processing
could bring significant and costly “collateral damage”. BGAs could require pre-bakes,PWBs may degrade and optoelectronic
components could fail or suffer reduced lifetimes. The next -generation sub-micron CPUs,with evolving low k dielectric
layers,may not tolerate excessive soldering temperatures. These problems may be "fixed",but not truly solved. Cost-adding
work-around strategies include higher performance laminates,upgraded molding compounds and in-process cooling,but
considerable time and money will be needed to re-engineer,re-test and re-qualify.
Polymer Solders (Conductive Adhesives) have provided a good alternative for temperature-limited assembly for decades.
These well-tested joining materials process like solder on the same equipment. Fluxing or cleaning is never required. And
they run at more than 100 degrees lower than solder. Both reflow and batch ovens can be set at 110oC to 150oC to quickly
harden these polymer systems. Adhesives are used to assemble SMTs to a variety of systems including medical devices,
memory modules,and computers. Chances are that LEDs in your business phone and ink jet printer are assembled with
conductive adhesives. Perhaps the flip chips driving your flat panel display are adhesively bonded.
This paper will compare Polymer Solders to L-F alloys to show limitations and advantages for the technology. There are
important restrictions,especially lower mechanical strength revealed in the drop test. But adhesives research has been
energized after years of simple incremental improvements and fresh new approaches will be summarized that include
intrinsically conductive polymers (ICP) and Nanomaterials.

Quantifying SMT adhesive dispensing performance has typically been attribute analysis via a microscope. Individual
adhesive deposits were inspected for strings or tails,extra dots,missing dots and dot diameter. These attributes were typically
measured with an eyepiece reticule and a light microscope. This tedious and subjective method has been replaced by a highly
quantitative,extremely quick automated method using the vision engine of a real time X-ray. The details of this method are
discussed as well as practical applications for glue benchmarking and dispense parameter fine-tuning. The output of this
method includes dot diameter,spherocity and area. Adhesive deposit consistency of both dispensing and printing are
compared using this novel measurement method.